MR2 Owners Club Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-11 of 11 Results
  1. MKI Cooling & Charging
    I recently purchased a 1985 mk1 with the 4age engine. I’ve tested the temp sensor in the engine bay, and the one on the radiator. They both get around 6V I tested the wires to the fans and there’s nothing, but I directly connected the fans to a separate battery and they ran fine. The engine bay...
  2. 3SGTE Turbo
    Finally picked up a JOBD reader for my gen 4 and see that it has a p0110 code. No other notable codes but that one. Could this be the cause of my lean idle problem? (Seemingly normal idle rpm, just the afrs are off. 16-18 on cold start, 15-16.8 when warmed up. afrs seem normal when in boost...
  3. MKI, 84-89 NA & SC
    Hey everyone, I've been slowly getting my car ready to pass smog. I've replaced my federal intake mani with a California one, but there are some sensors that I'm unsure what they connect to. I also replaced the TVIS, which did not have the VSV at all. I checked every gallery on PBase and google...
  4. MKI, 84-89 NA & SC
    I understand that it attaches to the EGR valve and connects to an EGR switch but I can't seem to find a diagram showing where specifically in the engine bay it connects. Currently converting my non-EGR AW11 to EGR so that it can pass California smog, so any advice is greatly appreciated. Thanks
  5. 1990-1999 MR2 Parts Swapper
    The story (skip to next page if not interested): My journey begins summer 2012 (just can't believe it's been 6 years already, shame). I found this thread by Bill Strong: https://www.mr2oc.com/47-road-racing/448543-free-wifi-lapper-droid-lap-timer-data-even-kitchen-sink.html and within it I...
  6. 1990-1999 MR2 Parts Swapper
    SOLD This is a brand new crank pulley and new bolt. Attached to the new pulley is a 60-2 trigger wheel for a possible COP set up. The sensor needed to run this with the appropriate spacing is included as well. I am asking $120 shipped in the 48 states. I accept paypal gift or cash. You can...
  7. MKII, 90-99 NA & Turbo
    Ok so before everyone tells me to put in an aftermarket gauge let me tell you that's not what I want. I have swapped in a 1mz V6 with a TRD S/C and I want to keep the rest of the car as stock as possible. If anyone got into my car that didn't know a lot about an MR2 they would think it was a...
  8. 1990-1999 MR2 Parts Swapper
    Hey I'm looking for an oil level sensor for my 1993 mr2 turbo...please pm me with a price shipped to Los Angeles .... Thanks
  9. 3SGTE Turbo
    HELP, need someone to loan me a spare knock sensor I'm having hesitation issues and believe it's my aftermarket Knock sensor. the only way that i can really test my theory with my knowledge is to swap if for the OEM. If anyone has an OEM preferably for the Gen 3 that could send it to me. I...
  10. MKII, 90-99 NA & Turbo
    Hey guys, I'm trying to finish up my build and ran into couple issue: 1. the Radiator & AC fans only works when I unplug the radiator fan sensor 2. is it normal only the driver side coolant pipe in the frunk is hot and the passenger side is cold? 3. the RPM is not working, which wire from the...
  11. MKII, 90-99 NA & Turbo
    Hey guys, I recently bought a 92 Turbo and I love her to death but she's developed a problem. When I drive and go up a hill or press the pedal down, the engine cuts out and the check engine light turns on, and it only gives me spurts of power until I stop asking the engine for so much. This only...
1-11 of 11 Results
Top