MR2 Owners Club Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 26 Results
  1. MKII, 90-99 NA & Turbo
    So i have a 98 1mzfe engine, and a 91 NA mr2 transmission. I have the V6 flywheel, but that's it. can anyone tell me what I need to get a clutch that will work with the engine and transmission? I read somewhere that I need the pressure plate that matches the engine? the engine is from an Avalon...
  2. V6 MR2 Forum
    So... My 1991 MK2 MR2 came with a 1MZ-FE engine. Already pulled the engine and transmisson, as it needs a new transmission. What are my transmission options? Should I go with another stock transmission? The transmission that came with it was destroyed because it didn't mount up to the 1mz-fe...
  3. General MK1 - FAQ
    I am having issues with my clutch it won’t shift into gear when the engine is running. The clutch pedal is very soft when pushed but will still go back to the original position. I can change the gears but only when the car is off. I am wondering what’s up with it
  4. 3SGTE Turbo
    So today I went for a drive and while on the highway I went to change gears but my clutch went to the floor with no resistance. I was still able to switch gears but the clutch pedal only had like a half inch to inch of play. I had to hook my foot behind the pedal to pull it back out. After it...
  5. 1990-1999 MR2 Parts Swapper
    Southbend Stage 2 Endurance clutch kit used in my E153. Come with everything in box, pressure plate, clutch disk, pilot bearing and exedy throwout bearing (throw those last two out lol) Has only about 800 miles on it, clutch disk still looks new. Nothing wrong with it, just pulled for a...
    $400 USD
  6. 3SGTE Turbo
    So basically, I can't shift into first from a stop/its very difficult to do so. What I've been having to do is force it into second first and then it'll go into first smoothly. When the car is moving, it shifts perfectly fine into all gears. When the car is off, it shifts perfectly fine into all...
  7. Normally Aspirated
    Hey guys, curious as to what the going rate for a clutch replacement is. 93 na in NE Ohio. Gotten a couple of quotes, $800 and $1300. The 1300 seems high. I've worked parts to be around ~$300-400 depending on how much you replace while the trans is out. I'd do it myself but it'd be a first...
  8. MKII, 90-99 NA & Turbo
    I'm back with another strange question about my 1991 NA MR2. So I took it out for a test drive. It drove fine for about 5-10 minutes, then out of nowhere, it started seeming like my clutch was slipping. It would rev up with little to no increase in speed or power. Each time I pressed the clutch...
  9. MKII, 90-99 NA & Turbo
    The clutch on my '95 N/A slips so I've been looking for a replacement, and with it, a lightweight flywheel, as of now I'm thinking of the exedy OE replacement clutch kit and Fidanza lightweight flywheel. I wouldn't be pushing more than 150 hp through this clutch as I'd be getting a new one with...
  10. 3SGTE Turbo
    Back again with another problem, this was happening before and after my clutch replacement. My pedal will SOMETIMES stick to the floor, SOMETIMES it will stick about 3/4 the way up on the return. Is this indicative of a bad master or something else? I don’t get slipping or any issues with clutch...
  11. MKII, 90-99 NA & Turbo
    Hey all, doing a clutch job on GM car and replacing the flywheel. I need new dowels for the new flywheel. Is there a part number anywhere?
  12. MKII, 90-99 NA & Turbo
    Hello, now that my car runs I'm fairly certain it needs a clutch... Just want to be sure before I spend several hundred dollars on replacing it that it's my issue. I attempted to adjust the clevis, this made no difference other than causing the pedal to stick to the floor if it was adjusted too...
  13. General MK2 FAQ (Newbie Center)
    1992 (mfd. 1991) MR2 T-Top 3S-GTE Turbo 5-speed -734/E153 185k Miles Car is only driven in city/highway, I've never tracked it. Hey all, going to need to replace my clutch pretty soon. So far I've decided to not only replace the clutch and pressure plate with the Exedy OE Replacement but also...
  14. Normally Aspirated
    I'm doing my clutch and flywheel soon on my gen 3 3sge MR2. I want to replace the flywheel bolts at the same time. I found a set of ARP bolts but they are only for the 3sgte (Part number: 203-2801) Would these fit the 3sge bolt holes? I'm not sure if the 3sgte and 3sge share the same flywheel...
  15. Common Engine Swaps and Related Discussions
    Hey guys I just got my gen 2 3sge swap running and went to go drive it and won’t go into gear. So I pull the engine back out and split the tranny from the engine and saw no obvious issues. I think I’m using the wrong flywheel or possibly clutch kit. What’s on the engine now is a 3sge flywheel...
  16. 1984-1989 MR2 Parts Swapper
    Matrix Garage WAT Coilover kit, Adjustable monotube shocks, 10k front, 8k rear, optimized for an "Inverted Xhead" set up. This setup is very competitive in Autocross. These are probably the best quality coilovers on the market, just ask yoshimitsuspeed. I paid $1400 for this setup, used for 2...
  17. MKI, 84-89 NA & SC
    I recently bought a 1987 mr2 (manual) which was in need of a new clutch. So it took about two weeks to finish the job and once I was ready to start the car the lights turned fine but when I attempted to turn the car over there was a loud clunk and the car died not even the lights would turn on...
  18. MKI, 84-89 NA & SC
    Hey everyone, so my 1985 MR2 recently had a problem where the clutch master cylinder was leaking. I ordered a replacement and installed it and long story short the threads on the flare nut where it connects to the master cylinder got stripped. Since the end of the clutch line is flared I don't...
  19. MKI, 84-89 NA & SC
    Help! Need 212MM Flywheel Hey guys, I'm (very) new to the MR2 scene. I actually just picked up an 87 for super cheap (yesterday)... but im pretty sure the clutch is blown up. Yes, actually blown up. Its crazy hard to get in gear and makes insane noises when in idle, they go away with the clutch...
  20. MKI, 84-89 NA & SC
    Hey guys, I had some trouble a week or so ago with my '85. I stepped on the clutch pedal and that puppy went straight to the floor. I saw that there was leaked brake fluid in the frunk (corroding some paint :frown2:) so I replaced the master cylinder. I bled the system. It was working fine but...
1-20 of 26 Results
Top